Відео

Yes, you can roll it on like this, strain to pull it and squash your fingers, or you can simply use the provided hole for a 1/2" drive pull bar in the tensioner bracket. Use leverage to take the tension off the belt and just drop it on.

Do you recommend on my 2001 f150 V6

How long it take you to get everything done

You made my day, Kevin. I always hated peeling eggs. Today we hardboiled about 5 dozen eggs to make red beet eggs. I followed your advice and added salt to the water. We do not use Morton salt so I used Redmans Real Salt, about a small scoop per dozen eggs. They all shelled perfectly except one which might have been cracked before hand. Some eggs we used were old and some were fresh but that did not make a difference! I notice this video had very high views which tells me there are a lot of people out there that have had trouble peeling eggs Again thanks much.

Hey man, are you using this pressure washer on a 14 amp breaker or a 20? Good video sir!

wow

Looks like you have the headers on the wrong ends

Your video is very informative,the tips helped out tremendously. But yeah thanks for being so thorough this was the best video of all I watched about changing out fuel pump..

There is a latch on the back of your seat to pop the seat up and out of the way Good video 😎

Some one please answer these questions how come when i had my old belt on it never was squealing i put a new belt on and its squeals alot also before i put the new belt on my bike would stop by its self when let off throttle wit new belt on it just keeps rolling when let of throttle someone please help?!

Love hearing you all. That's what we say here in KY.

why not just add ice to the cool water to cool down the eggs.???

I believe contaminated oil is the culprit for many engine problems. Once the oil has deteriorated it poisons gaskets, rubbers and everything else with its acidic properties. You find cars with regular oil change intervals to run smoothly and having no leaks after 20-30 years on original rubber parts.

Damn! The best YT video about this charger, for sure. Thank you so much ! It helps me a lot!

Instead of pulling the tensioner by hand, atleast in some models they provide a square hole on the arm of the tensioner that fits a ratchet so you can privet the pulley that way.

That’s a fake Microtech bud

Is the oil fully synthetic or semi synthetic

this work for clutches that wont engage?

Are they reliable motors

Thanks for posting this video

You should’ve installed a single din instead.

I use an air chisel to clean mine. Works very well.

After about 5 years I’m finally installing my wife’s radio Thank you for this. Best video I’ve seen

This could’ve been a 30 second video Quit wasting my time

Hey, thanks for making this video, I needed to check where the oil filter was located before I started to do it myself. I hope you are doing well.

Thanks for the info, I just bought a 2024 and it is exactly the same, right at the bottom of the hash mark. Yamaha must be being cheap with the oil :)

Thanks kevin

6 quartz of oil is like 5.6ltrs. Is that gallon 5.6ltrs or did you have to pour another 0.6litres to balance tjings up?

02 f150 king ranch 5.4 mint condition! This is the 10th generation comment section where yall at?

All of this is great, but mine is stuck pushed in around a quarter of an inch with zero room to insert anything around, above, or below it.

Most important thing to point out is that the knives are designed for impact and scraping which is why they are chisel ground

Worked perfect for a 2008 650 Brute Force.There are a few versions depending on year and whether 650 or 750. Thanks a lot!!!

This is a job where you wish you had a third hand

Hey man i tryed putting my switch back to on but it seems like its not clicking and goes back to the middle somewhat. Can you tell me what the part is called?

Mine flashes quickly but then stops what do I do

Can i hookup my sony atmos speakers with this amplifier

Thank you!

Thank you brother. Saved me a trip to repair center!

Some salt definitely goes into the egg. The process is called osmosis. Osmosis is something goes from a high concentration to low concentration through a membrane. Egg shells are porous membranes believe it or not. Won’t be a lot, but there will be some transfer.

So if I do this it won’t cause any further problems ?I got a Parari 700 vtwin

Turn the screws to the passenger side or to the left to lower and turn them to the driver side to raise. It's the same direction on both sides.

Just came across your video. It’s not nice to copy post 10. He’s first last and forever and nobody’s better looking than him anyway.

Thank You!

Just for archival purposes the problem with the walbro carbs on theae saws was the vent didn't work. Take off the top cover, drill a hole in it, reinstall.

Salt is stupid, it's just raising the temperature by 1 degreee, NO EFFECT at all, same with Vinegar, it just breaks down a bit of the Calcium, it's merely a ton of myths that people still believe, it's stupid

This video helped me a lot, I’m a 17 yr old and this was my first time changing oil in my ford edge. Super helpful

I am 6 years late but great video

What about crocodile eggs?😅

i have no idea if anyone will reply. so i add coolant to the reservoir then the radiator itself, run it to operating temp, top off if needed then run it one more time?

Great video ihavea brute force300 wasn't moving after kidflipoed it electric don't work as far seeing gages but now runs with battery but iput in high seems ok it soon swithto low seems lose almost all power barely goes ten kmh so seems only best working in high or skip right past gear anyone know what's wrong how fix this I'm not mechanical or much atvknoweldge I moved and alot stuff here is ATVs durtbikes so git this and now this issue ineed help advice from anyone please thnks